Art Glass Poppies!

Orange fused glass poppy
Orange fused glass poppy
I have been slowly working my way through the products I picked up this year at the Glass Craft and Bead Expo in Las Vegas. One of the "must see" stops on my list in the exhibit hall is Creative Paradise's booth. They make lovely fused glass casting and texture molds, and it's always fun to see what new items they have.

This year I picked up a Large Poppy mold (LF113). Creative Paradise has a couple of great tutorials on their site for casting into the mold and for using various sizes of frit in the mold (see link below). However, I wanted to see what effects I could achieve using powders and sheet glass. Following is a short tutorial on how I created poppies using powders and sheet glass.

Yellow-orange poppy
Yellow-orange poppy

Tutorial

Begin by treating the mold with MR-97. I use a 1.5" paintbrush to brush out the mold, and then give the mold a couple of quick sprays with MR-97. (Color de Verre has good information on their web site about coating molds with MR-97, see link below.) Do not overspray the mold -- too much MR-97 may be hard to remove or dull the finished piece.

After the mold has dried at least 15 minutes, begin filling the mold with powders. I like to place molds I am working on, on short 1/2" kiln posts so that it's easier to pick up the mold later without tipping it. For the yellow-orange poppy (shown in a stand on the right), I put down powder as detailed below. Note that all powders listed were System 96 opals.

Fill center with black powder.
Cover black powder with white.


Fill the center with a small amount of black powder, and use a little black powder in the ribs of the poppy for shading. Use the black very sparingly -- too much can overwhelm the other colors.







Cover the black powder in the flower center with white.




Sift down marigold powder.
Sift down orange powder for shading.



Sift some marigold over the center, and then sift marigold along the sides of some of the petals for shading.






Put down some orange for more shading.



Sift down yellow powder and white highlights.


Now sift down yellow on some of the petals, and add white on some edges for highlights.





Completely cover with sunflower powder.


Cover the entire area with sunflower powder. Try to get sufficient coverage so that when the piece is fired, you have a good solid background of color.
Clean powder from edges and top with clear.


Use a small paintbrush to clean the over-sifted powder from the edges of the mold, and top the mold with two 10.25" circles of clear glass.
Close-up of clear resting on edges of mold.


The glass should be just large enough so that it rests on the top edges of the mold. It should not fit down inside the mold, as doing so will be more likely to trap air and cause bubbles.





Firing Schedule

I tested this firing schedule in two of my kilns, a Skutt GM1414 and a Paragon Fusion 14, with consistent results in each. However, you may need to adjust the schedule for your particular kiln or if you use 90 COE glass.

Segment
Rate
Target
Hold
Ramp 1
300
1100
30
Ramp 2
50
1250
60
Ramp 3
500
1460
15
Ramp 4
1500
950
90
Ramp 5
100
700
00

Note that both of these kilns are firebrick and cool quite slowly. Firing time was 13.5 hours, and then I let the kilns cool normally to room temperature (several more hours). Notice the long hold for the bubble squeeze (ramp 2).

Here's the yellow-orange poppy after firing (also pictured in stand, above).

Yellow-orange poppy
Yellow-orange poppy


Close-up, yellow-orange poppy
Close-up, yellow-orange poppy

















Here is the powder layout for the orange poppy shown completed at the top of this post. Colors include black, yellow, plum, red, marigold, and orange:

Powder layout, orange poppy.
Powder layout, orange poppy.

Covered with orange powder. Clear glass on mold edges.
Covered with orange powder.
Clear glass on mold edges.











This is after firing, before slumping.

Orange poppy before slumping
Orange poppy before slumping
Close-up, orange poppy
Close-up, orange poppy


















The orange poppy was slumped into this mold:

Slumping mold
Slumping mold











Here is a bright yellow poppy. The powders used were white for the center, orange for coloring the veins near the center, and topped with yellow powder.

Bright yellow poppy
Bright yellow poppy
Close-up, bright yellow poppy
Close-up, bright yellow poppy


When choosing powders for any project, keep in mind that sulfur-bearing glasses (reds, yellows, oranges) will react with copper-bearing glasses (blues, greens). The reaction can produce murky, undesirable results. If you want to use copper- and sulfur-bearing glasses in the same project, make sure they are separated from each other with a non-reactive glass (white, clear, and celadon are a few). See Resources below for another blog post on reactions and working with powders.

Bubbles

There is always a concern when using full sheets of glass with a fusing mold. There are two factors that minimize the bubbles in the fired poppies. First, the glass blanks were placed on the edge of the casting mold, not directly on the powder. Second, I used a slow, long bubble squeeze in the firing schedule. Both of these result in the center of the glass falling onto the powder first, which allows the air to be squeezed out as the glass levels into the mold from the center to the outside edges. While the poppies do have some small bubbles, they are on the backside of the glass and do not detract from the finished project (in my opinion). Here are pictures of the bubbles in both the yellow-orange and orange poppies.

Back of yellow-orange poppy
Back of yellow-orange poppy

Back of orange poppy
Back of orange poppy












I hope you have found this information useful, and can use some of the ideas in your own work with either Creative Paradise's Large Poppy mold, or another mold of your own.

Thanks for reading!

Dana

Resources



Want to learn more about fusing? Bullseye Glass offers educational videos for a small annual subscription fee (click the banner below):
Bullseye Kiln-glass Education Online

Popular Posts